Oscilloscopes-Oscilloscope HANTEK DSO5102P1.Feature100MHz bandwidths1GSa/s Real Time sample rateLarge (7.0-inch) color display,WVGA(800x480)Record length up to 40KTrigger mode: edge/pulse width/line selectable video/slop/overtime etc.USB host and device connectivity, standardMultiple automatic measurementsFour math functions, including FFTs standardProvides software for PC real-time analysisVGA Optional2.SpecificationsModel : DSO5102PAcquisitionSample Rate : Real-Time Sample: 1GS/sAcquisition Modes Normal : Normal data onlyPeak Detect : High-frequency and randon glith captureAverage : Wavefom Average, selectable 4,8,16,32,64,128InputsInputs Coupling : AC, DC, GNDInputs Impendance : 1MΩ±2% ‖20pF±3pFProbe Attenuation : 1X,10XSupported Probe Attenuation Factor : 1X,10X,100X,1000XMaximum Input Voltage :CAT I and CAT II: 300VRMS (10×), Installation Category;CAT III: 150VRMS (1×);Installation Category II: derate at 20dB/decade above 100kHz to 13V peak AC at 3MHz* and above. For non-sinusoidal waveforms, peak value must be less than 450V. Excursion above 300V should be of less than 100ms duration. RMS signal level including all DC components removed through AC coupling must be limited to 300V. If these values are exceeded, damage to the oscilloscope may occur.Horizontal System :Sample Rate Range : 500MS/s--1GS/sWaveform Interpolation :(sin x)/xRecord Length : 40KSEC/DIV Range : 4ns/div to 40s/divSample Rate and Delay Time Accuracy : ±50ppm(at over any ≥1ms time interval)Position Range :20ns/div to 80us/div; (-8div x s/div) to 40ms;200us/div to 40s/div; (-8div x s/div) to 400sDelta Time Measurement Accuracy (Full Bandwidth) :Single-shot, Normal mode:± (1 sample interval +100ppm × reading + 0.6ns);>16 averages:± (1 sample interval + 100ppm × reading + 0.4ns);Sample interval = s/div ÷ 200Vertical SystemVertical Resolution : 8-bit resolution, all channel sampled simultaneouslyPosition Range : 2mV/div to 10V/divBandwidth : 100MHzRise Time at BNC(typical) : 3.5nsAnalog Bandwidth in Normal and Average modes at BNC or with probe, DC Coupled : 2mV/div to 20mV/div, ±400mV; 50mV/div to 200mV/div, ±2V500mV/div to 2V/div, ±40V; 5V/div, ±50VMath : +, -, *, /, FFTFFT : Windows: Hanning, Flatop, Rectamgular, Bartlett, Blackman;1024 sample pointBandwidth Limit : 20MHzLow Frequency Response(-3db) : ≤10Hz at BNCDC Gain Accuracy :±3% for Normal or Average acquisition mode, 5V/div to 10mV/div;±4% for Normal or Average acquisition mode, 5mV/div to 2mV/divDC Measurement Accuracy,Average Acquisition Mode :When vertical displacement is zero, and N ≥16:± (3% × reading + 0.1div + 1mV) only 10mV/div or greater is selected;When vertical displacement is not zero, and N≥16: ± [3% × (reading + vertical position) + 1% of vertical position + 0.2div]; Add 2mV for settings from 2mV/div to 200mV/div; add 50mV for settings from 200mV/div to 5V/divVolts Measurement Repeatability,Average Acquisition Mode : Delta volts between any two averages of ≥16 waveforms acquired under same setup and ambient conditionsTrigger SystemTrigger Types : Edge, Video, Pulse, Slope, Over time, AlternativeTrigger Source : CH1, CH2, EXT, EXT/5, AC LineTrigger Modes : Auto, Normal, SingleCoupling Type : DC, AC, Noise Reject, HF Reject, LF RejectTrigger Sensitivity(Edge Trigger Type) :DC(CH1,CH2):1div from DC to 10MHz; 1.5div from 10MHz to 100MHz; 2div from 100MHz to Full;DC(EXT): 200mV from DC to 100MHz; 350mV from 100MHz to 200MHz;DC(EXT/5): 1V from DC to 100MHz;1.75V from 100MHz to 200MHz; AC: Attenuates signals below 10Hz;HF Reject: Attenuates signals above 80kHzLF Reject: Same as the DC-coupled limits for frequencies above 150kHz; attenuates signals below 150kHzTrigger Level Range :CH1/CH2: ±8 divisions from center of screen;EXT: ±1.2V;EXT/5:±6VTrigger Level Accuracy(typical)Accuracy is for signals having rise and fall times ≥20ns : CH1/CH2: 0.2div × volts/div within ±4 divisions from center of screen;EXT: ± (6% of setting + 40mV);EXT/5: ± (6% of setting + 200mV);Set Level to 50%(typical) : Operates with input signals ≥50HzVideo Trigger Video Trigger Type : CH1, CH2: Peak-to-peak amplitude of 2 divisions;EXT: 400mV;EXT/5: 2VSignal Formats and Field Rates, Video Trigger Type : Supports NTSC, PAL and SECAM broadcast systems for any field or any lineHoldoff Range : 100ns~10sPulse Width Trigger Pulse Width Trigger Mode : Trigger when (< , >, = , or ≠); Positive pulse or Negative pulsePulse Width Trigger Point :Equal: The oscilloscope triggers when the trailing edge of the pulse crosses the trigger level.Not Equal: If the pulse is narrower than the specified width, the trigger point is the trailing edge. Otherwise, the oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width.Less than: The trigger point is the trailing edge.Greater than (also called overtime trigger): The oscilloscope triggers when a pulse continues longer than the time specified as the Pulse WidthPulse Width Range : 20ns ~ 10sSlope Trigger Slope Trigger Mode : Trigger when (< , > , = , or ≠ ); Positive slope or Negative slopeSlope Trigger Point :Equal: The oscilloscope triggers when the waveform slope is equal to the set slope.Not Equal: The oscilloscope triggers when the waveform slope is not equal to the set slope.Less than: The oscilloscope triggers when the waveform slope is less than the set slope.Greater than: The oscilloscope triggers when the waveform slope is greater than the set slope.Time Range : 20ns ~ 10sOvertime Trigger Over Time Mode : Rising edge or Falling edgeTime Range : 20ns ~ 10sAlternative Trigger : Trigger on CH1 :Internal Trigger: Edge, Pulse Width, Video, SlopeTrigger on CH2 : Internal Trigger: Edge, Pulse Width, Video, SlopeTrigger Frequency CounterReadout Resolution : 6 digitsAccuracy(typical): ±30ppm (including all frequency reference errors and ±1 count errors)Frequency Range : AC coupled, from 4Hz minimum to rated bandwidth
